or Connect
TheSandTrap.com › Golf Forum › The Pro Shop › Clubs, Grips, Shafts, Fitting › WITB Photo Edition!
New Posts  All Forums:Forum Nav:

WITB Photo Edition! - Page 28

post #487 of 843


Thought I would quote my post as have changed my bag and wedges and added a 3 iron a3_biggrin.gif

 

This bag is seriously lite as well.

Quote:


















 

post #488 of 843

That Redwood putter is sexy! I love the Redwood series!

post #489 of 843

Decided to post a couple new pics after the new additions: Added the R11 and a new Vokey 58° wedge.

 

IMAG0196.jpg

 

IMAG0197.jpg

 

IMAG0198.jpg


Edited by Rebel_Golfer - 3/23/11 at 8:39pm
post #490 of 843

Since I love looking at all the posts here I decided to take some crappy photos of my clubs with my blackberry. Here they are hope they come out okay.

 

1.jpg2.jpg

 

3.jpg4.jpg5.jpg6.jpg

post #491 of 843

Here's my 2011 bag

 

Went into 2011 with the following setup
Titleist 983K 8.5 degree driver with Graffaloy Pro Lite shaft (stiff)
Titleist 980F 15 degree fairway wood with Dynamic Gold S300 steel shaft
Titleist 990 irons 2-PW with DG S300 shafts
TItleist Vokey 52 degree gap wedge
Titlesit Vokey 60 degree lob wedge
Cleveland 56 degree sand wedge
Scotty Cameron Teryllium Newport 2

Now I loaded up with the following (pics to follow)

Titleist 910 D3 8.5 with Titleist 'Ahina 72 Stiff (D4 setting) tipped .5 inches
Titleist 980F 15 degree fairway wood with Dynamic Gold S300 steel shaft
Titleist 9902 iron with DG S300 shafts
Titleist 710 MB 3-PW with DG S300 shafts (2 degrees upright)
TItleist Vokey 52 degree gap wedge
Titlesit Vokey 60 degree lob wedge
Cleveland 56 degree sand wedge
Scotty Cameron Teryllium Newport 2

 

DSC_0431.JPGDSC_0486.JPGDSC_0491.JPGDSC_0493.JPGDSC_0502.JPGDSC_0402.JPGDSC_0504.JPGDSC_0505.JPGDSC_0499.JPGDSC_0501.JPGDSC_0507.JPGDSC_0390.JPGDSC_0487.JPGDSC_0486.JPGDSC_0484.JPG

post #492 of 843

Well, I replaced the irons recently so I figured I'd post some pictures of my bag again...

 

Heres my set-up currently:

Driver - Mizuno MP-630 w/ Fubuki shaft (stiff)

3 wood - Adams Speedline 9032ti Hybrid FW (14.5 deg) w/ Voodoo SNV7 shaft (stiff)

Hybrid - Titleist 585h (21 deg)

Irons - Titleist 695 cb (4-PW)

Wedges - Callaway X Forged (GW, SW, LW)

Putter - Scotty Cameron Pro Platinum Laguna Two

 

My Bag 

Driver

MP630

3w

9032ti

Hybrid

585h

Irons

694cb 4-pw 695cb single iron

Wedges

Wedges 

Putter

Putter

post #493 of 843

So I switched up almost my entire bag for springtime:

 

OUT: TM Burner Superfast 9.5 S --> IN: TM R9 420 10.5 S

 

OUT: TM Burner Superfast 3W 15* S --> IN: Cobra Speed LD-F 3W 15.5* S

 

OUT: TM RAC Nickel 52*  --> IN: Cleveland Mashie 23* S

 

OUT: Bridgestone J36 Combo 4-P PX-6.0-F --> IN: Ping Eye 2 + no + 4-W ZZ Lite S

 

KEEPERS: Adams Super Hybrid 19* S, Scotty Cameron SS Fastback #1, Scratch JLM-SND 56*, Nike SV Tour 60*

 

IMAG0061.jpg

 

IMAG0063.jpg

 

 

 

 

 

 

post #494 of 843

So since im STILL waiting to get out for my first round of the year (thanks mother nature for snow on April 1st) I decided to regrip my irons and wedges.  Now I am good to go for the year!

 

IMG_20110401_123623.jpg

post #495 of 843


I have the same grips, I think you will be very pleased with that decision. Looks great.
 

Quote:
Originally Posted by toddmlazarchick View Post

So since im STILL waiting to get out for my first round of the year (thanks mother nature for snow on April 1st) I decided to regrip my irons and wedges.  Now I am good to go for the year!

 

IMG_20110401_123623.jpg



 

post #496 of 843

You will be happy playing the Ping Eye 2 I love mine.  best clubs imo
 

Quote:
Originally Posted by xxsoultonesxx View Post

So I switched up almost my entire bag for springtime:

 

OUT: TM Burner Superfast 9.5 S --> IN: TM R9 420 10.5 S

 

OUT: TM Burner Superfast 3W 15* S --> IN: Cobra Speed LD-F 3W 15.5* S

 

OUT: TM RAC Nickel 52*  --> IN: Cleveland Mashie 23* S

 

OUT: Bridgestone J36 Combo 4-P PX-6.0-F --> IN: Ping Eye 2 + no + 4-W ZZ Lite S

 

KEEPERS: Adams Super Hybrid 19* S, Scotty Cameron SS Fastback #1, Scratch JLM-SND 56*, Nike SV Tour 60*

 

IMAG0061.jpg

 

IMAG0063.jpg

 

 

 

 

 

 



 

post #497 of 843

Nice Todd, enjoy the new grips. They look good.

post #498 of 843

Thanks.  Ive had them on my R9 Supertri and my R9 3W and 09 Rescues.  My tackimac's were getting all marked up and looked like crap.  I should have black widowed my irons instead of tackimacing them originally.  

post #499 of 843

Mine seems to be about done. a1_smile.gif

 

CIMG0131.jpg

 

CIMG0139.jpg

 

CIMG0140.jpg

 

CIMG0156.jpg

 

(Yes, the 3 hybrid shaft went in cosmetically wrong. Don't drink and build clubs kids!)

 

 

post #500 of 843

1970's ? Dont think so , Iranian Shah's living room ? Probably ! Sweet clubs though .

post #501 of 843
I thought that it was time to update my WITB for 2011. Although not much has changed, I have made a few additions.

I currently have 2 bags; my primary "gamer" bag and a secondary bag of "backups". I seldom game my "backups" which is a real shame, it would be nice to replace them with another set of 1957's... I also have a few clubs that, depending on course/conditions/etc, I will rotate in from time to time.

Anyway, first my primary bag:

Driver: Callaway 9.5' FT Tour w/Diamana WB 73 S, D3, 44.5"
Fairway Wood: Titleist 13' 909F3 D3 w/Matrix Ozik Code 8 S, D3, 43"
Irons: Miura 1957 Limited Edition "baby blade" 2, 4-PW
Wedges: Miura 52/7, 56/9 & 60/7
Putter: Scotty Cameron Newport Button Back, 33", 360g (rwb)
Bag: 2011 Titleist 14-way

My backups:

Driver: Callaway 9.5' FT Tour w/Diamana WB 73 S, D3, 44.25"
Fairway Wood: Titleist 15' 909F3 D3 w/Matrix Ozik Code 8 S, D3, 43"
Irons: Miura Tournament Blade, 3-PW
Wedges: Scratch Tour Department 52 SND, 56 SFU & 60 EGG
Putter: Scotty Cameron Studio Select Newport, 33", 360g (rwb)
Bag: 2009 PING Hoofer

My extras:

Fairway Wood: Titleist 18' 909F3 D3 w/Matrix Ozik Code 8 S, D3, 42.5"
Irons: Miura 1957 Limited Edition "baby blade" 3-iron
Putter: Scotty Cameron Studio Select Newport, 33", 360g (purple)
Putter: Scotty Cameron Studio Select Newport, 33", 360g (red)
Putter: Scotty Cameron TeI3 Newport, 33", 360g
Putter: Scotty Cameron AOP Newport, 33", 360g
Putter: Scotty Cameron Button Back Newport, 34", 350g

My primary driver is a Callaway FT Tour with a spine aligned Diamana WhiteBoard 73 in S flex tipped about 1/4". The driver swings at 44.5" and is weighted at D3 via a little hot melt. This driver is gripped with a Golf Pride Tour Velvet Cord w/a single wrap of tape. My backup driver is virtually identical to my "gamer". Same shaft (spine aligned & tipped about 1/4"), same swingweight. Swings at 44.25" and is gripped with a black/purple Golf Pride Multi-Compound.

The fairway woods have all been custom built as well starting with stock clubs from Titleist. Shafts have been spine aligned and play just a tad stiffer than "stock S-flex" (like my drivers, tipped about 1/4"). The swingweights are set to D3 (hot melt when needed). They are all gripped with Golf Pride Tour Velvet Cords.

My primary irons & wedges were also custom built. Both my 57' & 62' wedges feature custom C grinds. Specs of my primary irons & wedges are as follows;
Code:
Club  Loft  Bounce Lie   Length   Swingweight  Shaft
2      19*   -1*   59*   39.5"      D2         S400 Sensicore Satin Hard-Stepped 1x
3      22*   1*    59*   39"        D2         S400 Sensicore Satin Hard-Stepped 1x
4      25*   4*    60*   38.5"      D2         S400 Sensicore Satin Hard-Stepped 1x
5      28*   6*    61*   38"        D2         S400 Sensicore Satin Hard-Stepped 1x
6      32*   6*    62*   37.5"      D2         S400 Sensicore Satin Hard-Stepped 1x
7      36*   6*    62.5* 37"        D2         S400 Sensicore Satin Hard-Stepped 1x
8      40*   7*    63*   36.5"      D3         S400 Sensicore Satin Hard-Stepped 1x
9      44*   9*    63.5* 36"        D3         S400 Sensicore Satin 36.5" Tour Wedge
P      48*   8*    64*   35.5"      D3         S400 Sensicore Satin 36.5" Tour Wedge
52     52*   7*    64*   35.5"      D4         S400 Sensicore Satin 36.5" Tour Wedge
57     57*   10*   64*   35.25"     D5         S400 Sensicore Satin 36.5" Tour Wedge (bent 56/9 w/C grind)
62     62*   9*    64*   35.25"     D6         S400 Sensicore Satin 36.5" Tour Wedge (bent 60/7 w/C grind)

Grips - Golf Pride Tour Velvet Cord, Logo Down, .580, 1 tape wrap

As you might expect, my backups were custom built as well. Specs are as follows (virtually identical to my 1957's);
Code:
Club  Loft  Bounce Lie   Length   Swingweight  Shaft
3      22*   1*    59*   39"        D2         S400 Sensicore Satin Hard-Stepped 1x
4      25*   4*    60*   38.5"      D2         S400 Sensicore Satin Hard-Stepped 1x
5      28*   6*    61*   38"        D2         S400 Sensicore Satin Hard-Stepped 1x
6      32*   6*    62*   37.5"      D2         S400 Sensicore Satin Hard-Stepped 1x
7      36*   6*    62.5* 37"        D2         S400 Sensicore Satin Hard-Stepped 1x
8      40*   7*    63*   36.5"      D3         S400 Sensicore Satin Hard-Stepped 1x
9      44*   9*    63.5* 36"        D3         S400 Sensicore Satin 36.5" Tour Wedge
P      48*   8*    64*   35.5"      D3         S400 Sensicore Satin 36.5" Tour Wedge
52     52*         64*   35.5"      D4         S300 (SND)
57     56*         64*   35.25"     D5         S300 (SFU)
62     60*         64*   35.25"     D6         S300 (EGG)

Grips - Golf Pride Tour Velvet Cord, Logo Down, .580, 1 tape wrap

All of my Miura irons/wedges contain conforming grooves. My Scratch wedges, on the other hand, are non-conforming.

My putters are all Scotty Cameron Newports and I've got a multitude of (very similar) choices.

To start things off, I have 3 Studio Select Newports all 33" with 20g weights and Cameron cord grips (one red, 2 black). One has the stock paint theme and the other two have been tweaked slightly as shown in the pics. The red/white/blue putter has just those "cherry" dots changed, stock paint otherwise. My black/purple one has been changed as shown and has had the paint stripped from the sole.

I also have a pair of Newport Button Backs. The one with the polished insert has been shortened to 33" and sports 20g weights and a black Cameron cord grip and red/white/blue paint. The other one is bone stock, plays to 34" and has the factory 15g weights and the leather stitchback grip and headcover.

To round out my flatsticks, I also have a Cameron AOP (Art of Putting) Newport and a Sole-Stamp TeI3. Both of these sticks have had the stock shafts swapped out with new ones and now play to the 360g/33" configuration that I prefer. I swapped out the shafts (and weighted via tungsten powder) so that I could return them to stock when/if I decide to in the future.

My primary gamer, as in 90%+ of my rounds, is my red/white/blue Button Back and it lives under the blue Odyssey headcover that you see in the pics. I strongly prefer this headcover due to it's slim size and magnetic closure (if only I could find one in black). My "backup" is my red/white/blue Newport. I just had my AOP and TeI3 modified to fit me better though so that slot in my bag just might be up for grabs.

As noted in my signature, I use all of this gear to smack around either a TaylorMade Penta TP or a Bridgestone B330-S.

At the moment I'm very happy with both of my bags. Although, I would like to make a few changes (wouldn't we all);

1 - I'd really LOVE to swap out my TB heads for some CC 1957 heads. This would allow me to put my bags in a regular rotation. I strongly prefer the 1957's and would love to "standardize" on them for my irons.
2 - I'd like to replace my Scratch wedges with something that has CC grooves. I've been debating over going with a 53'/58' setup to open another slot at the top of my bag. I'm not sure that I want to do this though since I've very comfortable with my 52'/57'/62' setup.
3 - I'd like to get my hands on another TeI3, preferably another sole-stamp, in rough shape that I can send out for a deep milling. I think that this would be the ultimate in a soft feeling putter.

Enough rambling, on to some pictures...

Putters...
witb1.jpg

witb2.jpg

witb3.jpg

witb4.jpg

witb10.jpg

witb12.jpg

Miura 1957 & TB 3-irons...
witb5.jpg

Miura 1957 & TB 7-irons...
witb6.jpg

My gamers...
witb8.jpg

My backups...
witb11.jpg

witb-10.jpg

Scratch wedges...
witb-9.jpg

Well, that's my current WITB... Thanks for checking it out.
post #502 of 843

My current setup, other than I have taken the Cleveland driver out and put my Diablo Edge back in.  For good this time.  f3_laugh.gif

 

DSCN0655.JPG

 

DSCN0658.JPG

post #503 of 843

My 2011 Bag

 

Titliest Lightweight Cart Bag

Grips: Golf Pride New Decade (all clubs)
 

Driver: TM R9 460 

Woods: 2007 TM Burner 3 Wood, 2007 TM Burner 5 Wood(not pictured)

Hybrid: 2007 TM Rescue 3H, 2009 TM Rescue 2H

Irons: Nike VR Full Cavity 4-AW UST Graphite Shafts
Wedge: Titliest Vokey 56o, Cleveland CG15 56o, TM TP xFT 56o, TM TP xFT 52o(not pictured) 

Putter: Nike Method Core MC-1i 34inch

 

DSC_0003.JPG

DSC_0008.JPG

DSC_0005.JPG

DSC_0011.JPG

DSC_0014.JPG

 

post #504 of 843
Here are my sets

af90cf3e-35d3-1b32.jpg

af90cf3e-35f6-8990.jpg

af90cf3e-3618-993c.jpg


af90cf3e-3637-0733.jpg

af90cf3e-3688-5872.jpg
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Clubs, Grips, Shafts, Fitting
TheSandTrap.com › Golf Forum › The Pro Shop › Clubs, Grips, Shafts, Fitting › WITB Photo Edition!