Jump to content
IGNORED

Maltby Clubmaking/Repair Manual


Note: This thread is 737 days old. We appreciate that you found this thread instead of starting a new one, but if you plan to post here please make sure it's still relevant. If not, please start a new topic. Thank you!

Recommended Posts

Does anyone have a copy of this?  It is the hard copy one that is over 500 pages.  In the older edition there was a section that showed each shaft and gave specs on them including weight, trim instructions, tip length, step pattern etc.  It contained the specs for all the common steel shaft from the 60s-80s.  I am trying to find this information on the TT JetStep steel shaft.

Link to post
Share on other sites

  • iacas changed the title to Maltby Clubmaking/Repair Manual

Wood - UJWC = 1" steps.  .600 butt dia.  .335 tip.  47".  131 grams.  

 

Irons - UJIC(.370) UJCIO (.395) = 1" steps.  .600 butt dia.  41".  129 grams

 

irons - JTIS/JTISR = 1" steps.  .580 butt dia.  .355 tip dia.  35"-39" 120 grams

 

All I could find on trimming is pretty much the standard.  0" for 1 iron/1/2" for 2 iron/1" for 3 iron, etc.  

HTH

 

Edited by denkea
tip dia correction
Link to post
Share on other sites

mine are the UJCIO (over hosel)  I am trying to fix up an old set of Spalding XE hyprid irons.  Some of the shafts look like they have been cut  because they broke off at the hosel etc.  Knowing the raw length should help me figure this out.  The PW is the worst while the 3 iron is off about an inch.  Thanks

Link to post
Share on other sites

2 hours ago, Buzzy said:

mine are the UJCIO (over hosel)  I am trying to fix up an old set of Spalding XE hyprid irons.  Some of the shafts look like they have been cut  because they broke off at the hosel etc.  Knowing the raw length should help me figure this out.  The PW is the worst while the 3 iron is off about an inch.  Thanks

Wow!  Good luck with that.  I don't envy you that job.  But,,,,,have fun though.

Edited by denkea
Link to post
Share on other sites

thanks, i think i will need to tip some shafts and extend the length is some

the guy that had these put brand new grips on them in order to sell them;  they did not sell so my friend who owns the course just gave them to me as he knows i tinker with clubs

Link to post
Share on other sites

Not sure if these might help but Leaderboard golf has some .385 tip shafts available.  41"

 

314472064.jpg?fit=200%2C216&ssl=1&w=1400

The Multi-Step is designed with a low kick point for players seeking higher launch angles from a steel shaft. Features a unique step patterns that creates tip flexibility for higher trajectory. Ext…

Who knows.  Might help?!?

 

Link to post
Share on other sites

Note: This thread is 737 days old. We appreciate that you found this thread instead of starting a new one, but if you plan to post here please make sure it's still relevant. If not, please start a new topic. Thank you!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Want to join this community?

    We'd love to have you!

    Sign Up
  • Support TST Affiliates

    TourStriker PlaneMate
    Golfer's Journal
    Whoop
    SuperSpeed
    FlightScope Mevo
    Use the code "iacas" for 10% off Mevo and the code "iacasjun21" for 10% off SuperSpeed.
  • Posts

    • Played 27 Holes today made 7 birdies today finally birdied the 1st, just the second and third left to birdie.
    • I’ll pass that along to him and his people.  👍
    • Played my second round (ever) at the course that I think will be a home course for me next year (the complex has two 18s... I have played the other 18, but not in over a decade).  Birdied #13 to improve my away composite to five birdies and a total of -4 (I still have yet to par a hole nine in 2021 ... anywhere).  My two-round composite at that course is a 77.  By contrast, no birdies so far at my home course (well beyond two rounds played... and at least three scheduled in the next two weeks!), and three holes there I've yet to par.
    • Jesus, it’s not just white people who are offended. Just because he isn’t doesn’t mean many more native Americans are not. This line of logic is just idiotic. 
    • I talked to my buddy, 100% Navajo, about this thread.  His response was to shake his head, laugh and say “Leave it to the arrogant white man to tell us what we should be offended by…” Just thought I’d share.  I’m sure the arrogant white men here will continue to tell him he’s wrong though…  😂  
  • Today's Birthdays

    1. CrappyGolfer
      CrappyGolfer
      (68 years old)
    2. Jacob Vance
      Jacob Vance
      (25 years old)
    3. jax731
      jax731
      (54 years old)

×
×
  • Create New...

Important Information

Welcome to TST! Signing up is free, and you'll see fewer ads and can talk with fellow golf enthusiasts! By using TST, you agree to our Terms of Use, our Privacy Policy, and our Guidelines.

The popup will be closed in 10 seconds...