thefootwedge

I was hoping someone may know the "standard" (or as good as) head weights for todays clubs but I thank you all for your input.

Dear all, I came across the article/charts below at the weekend ( I know it is few years old). Apart from the length, how do the weights and swing-weights stand up to todays modern clubs. I am more concerned with the bottom chart STANDARD SWINGWEIGHTS CALCULATING THROUGH A SET rather than the SWINGWEIGHT FACTORS chart Are the any other charts for todays more modern clubs out there? Pre-Calculating Swingweight Swingweight Factors Swingweight Change Increase Factor By S.W. Factor Decrease Factor By S.W. Change +1 2 Grams Headweight 2 Grams -1 +3 1/2 inch Club Length 1/2 inch -3 -1 4 Grams Grip Weight 4 Grams +1 +1* 9 Grams Shaft Weight 9 Grams -1* The shaft swingweight equivalent is for illustration purposes only. Unlike the other three factors, as shaft weight changes its effect on swingweight changes at a disproportionate rate. For estimation purposes, however, the above shaft weight-to-swingweight equivalent is acceptable. Standard Swingweight Calculatin Through A Set Club Headweight Raw Shaft Weight Grip Weight Club Length Swingweight 1 Wood 198g 125g 52g 43" DO 3 Wood 208g 125g 52g 42" DO 4 Wood 213g 125g 52g 41.5" DO 5 Wood 218g 125g 52g 41" DO 7 Wood 228g 125g 52g 40" DO 1 Iron 230g 125g 52g 39.5" DO 2 Iron 237g 125g 52g 39" DO 3 Iron 244g 125g 52g 38.5" DO 4 Iron 251g 125g 52g 38" DO 5 Iron 258g 125g 52g 37.5" DO 6 Iron 265g 125g 52g 37" DO 7 Iron 272g 125g 52g 36.5 DO 8 Iron 279g 125g 52g 36" D0 9 Iron 286g 125g 52g 35.5" D0 PW 293g 125g 52g 35.5" D3 PW 305g 125g 52g 35.5" D6 Raw Shaft Weight is based on a 45" UDWS (parallel tip True Temper Dynamic S-flex for woods) and a 39" UDIC (parallel tip True Temper Dynamic S-flex for irons). With proper trimming and installation, each shaft's weight will drop slightly through the set. Grip weight is basded onthe average weight of an M58 Golf Pride Men's Green Victory rubber grip. Although both the UDWS and UDIC shafts possess .600" butt diameters, most clubmakers purchase M58 (.580 core) grips. Therefore, the above chart reflects the installation of a .580 core grip. Traditionally the sand wedge and pitching wedge are designed to play at higher swingweights than the 1-9 irons. Shaft balance point is a parameter that is dependent upon specific shaft trimming. This shaft characteristic may have an impact on swingweight as well, particularly with a tip heavy or butt heavy design. This table appeared in Clubmaker's Digest, Vol 11, Number 4. Issue No. 90 Thanks in advance Pre calculating swingweight.doc http://clubmaker-onl...ht.factors.html Pre calculating swingweight.doc

Scotty Heads and putter shafts in general are easy to bend. Just take it along to a pro with a putter loft and lie machine. Take 2 minutes and you can go up to about 5 degrees either way. The shaft is heated and bent in most cases for goose neck. Should only cost $3 or $4

The PGA Tour Superstores will fit you for free and they have a huge selections of used clubs. They will only charge you about $25 on top of the price to change the loft and lie angle. If you want to get an idea of what might fit you before you go, have a look on golfclubshaftreview.com. They have some great charts to help you out. Failing the PGA store, Try Golfsmiths but I'm not sure on their costs. Good luck

Club lengths keep changing over the years. They are getting longer due to a couple of factors, weight and manufactures trying to make clubs go further. Have a look on golfclubshaftreview.com where they have a club length page.

Having a shorter shaft on your driver will give you a lot more control. You may lose some distance but if you are landing on the fairway more often, the question is, 20 yards back or 10 yards in the rough. Remember, the old length for a driver used to be 43 inches. Theses days everything is going longer due to weight. Cut it down, if it feels a little light load it with lead tape. Your pro can always extend it again if you want to lenghten it.

Tour Velvet all day long. Lamkin grips are harder. That is not to say the TV's are a soft grip but I think you will be happy with the Tour Velvet.

If your grips are too big for your hands you will probably end up pushing or slicing on your bad shots. Grip pressure is a big part of golf although, if you have to go with a bigger grip to ease up on the King Kong grip then try it out on 1 or 2 clubs first before you spend $50 or $60 on a full set. Check out the grip size page on golfclubshaftreview.com

Shafts could be too stiff but my first thoughts are that the new Taylor irons are longer than most standard clubs. This could be your issue. Measure them up against your old clubs, if you still have them to se if this is the problem

Hogan Apex PC's. Amazing feel, great shafts if the #4 shafts are fitted. The E wedge was a preat PW which was amazing of tight lies.

Shaft swapping is fairly easy and can be a lot of fun to do yourself. Knowing your equipment is another story. Have a look on golfclubshaftreview.com for some good tips on replacing shafts and shafts specs.

You maybe trying to hit the longer irons too hard. D-Golds are a heavy-ish shaft so you may want to go with lighter. It is all trial and error and costs can go up. If you can go for a club fitting session you should be able to try a lot of different shafts. PGA tour super stores do this for free. Have a look on golfclubshaftreview.com for a good shaft fitting guide.

It is a way of changing the flex of your clubs buy swapping the shafts around. you can make your clubs softer or stiffer. Have a look on golfclubshaftreview.com They have a page dedicated to that subject. Hope this hekps

If you are on the border then my best advise, apart from trying other shafts, is to hard step the regular shaft Have the pro or repair shop cut the tip of the shaft half the three quarters of and inch and then add the lost length to the but end. This may be an added expense but it is a way of getting that in between stiffness. If you are a bit of a DIY expert, you could always do it yourself. Have a look on golfclubshaftreview.com for details on reshafting. Picking th correct shaft is a big question and takes a lot of thought as it can become pricey. ebay is a great way of buying clubs with different flexes without spending a bomb. Good luck

Think about the bad shots rather than the good. Is there a bad shot that you play with either club more often? If so, let me know and I will give you my best advice.

The hardest thing about changing shafts is filing down the ferrule and making it look good. Apart from that it is pretty easy stuff. I would go for 12 hour epoxy rather 18 hour and forget the 5 minutes stuff otherwise you could end up in a big fat mess. Have a look on golfclubshaftreview.com There is a page or DIY reshafting which will help you out.

The reason why you are slicing is probably because the lie of your clubs is too flat. If you are very upright then the toe of the club hit the ground first which opens up the club-face. Try getting the lie of your clubs adjusted. There is an interesting page about club length on club length on golfclubshaftreview.com Although club length is an open subject. Faldo is a giant and his clubs were an inch shorter than std and Woosenam were an inch longer. Club for the past few years now have been getting a little longer so experiment a little and have the lie adjusted first

Shaft recomendations is a tough subject. Two people who hit the driver the same distance can have very differnt shafts due to swing speeds, tempo and all sorts of other differences. Saying that, the Prolaunch Red with Speed Coat is a great shaft for a great price. Then consider having the shaft pured. There is a lot of good information on shaft selection on golfclubshaftreview.com Hope this helps

Shaft flex is a very wide open field. Shaft weight is also a big factor. Have a look on golfclubshaftreview.com they have a shaft fitting guide page that may well help you figure things out. Good luck

Grip fitting is really simple and easy, just takes a bit of patience. Check out golfclubshaftreview.com They have a grip fitting guide on their grip size page. Hope this helps

The blue 3M stuff is fine but just not as sticky as normal masking tape. 2" tape is what you want. For example, 4 wraps would be 3 of the masking tape on the shaft and the 4th would be your grip tape over the 3. You can use 4 wraps of grip tape but this would just be more expensive if you are fitting yourself. Most club fitters shouldn't charge you for the extra wraps unless you start asking for too many.

Measure from the butt end of the grip to the heel of the club. If you need to know club lengthes, check out golfclubshaftreview.com they have a club length page which will give you the lenghts you need for your height approximatley!

If you can 9 wraps of tape under a grip then good luck, 6 wraps is the most I ever fitted and that was for a giant of a man. Again, depending on butt size, 4 to 5 wraps will get you to midsize. 9 wraps without the grip maybe! Too many wraps will make the butt end of the grip feel weird. If you are trying to build to midsize or a fraction, the go to midsize and have them put on with only an inch of tape covering the butt end and have the grip stretched down a little but make sure whoever is fitting them knows what they are doing or your grips could end up in a big fat mess! good luck

Replace the rug before the clubs. I'm sorry, picture is a litle blured and need a better close up on the shaft bands. Although, they are cavity backed irons which will help your game if you have only been playing for a year. Add some clearer pictures and I will get back to you.

Check out golfclubshaftreview.com they have a page on grip size. When it comes to wraps, most people talk in terms of the double sided grip tape or standard 2" masking tape. I wear a ML and have 2, 3 or even 4 wraps under a standard grip depending on the butt size of the shaft. If the butt size is .600 I go with 2 wraps, if the but size is .580 I go 3 to 4. It depends on the grip. If you are wearing a large grip I would go with 3 - 4 wraps or see if you can find someone with a midsize grip and see if it feels comfortable. Although, if a grip is too big you may begin to push the ball off to the right a little. At the end of the day, what feels good is good.