Jump to content
Check out the Spin Axis Podcast! ×
Note: This thread is 4979 days old. We appreciate that you found this thread instead of starting a new one, but if you plan to post here please make sure it's still relevant. If not, please start a new topic. Thank you!

Recommended Posts

Posted

Hello,

I have a question about getting fitted for clubs. I found a set of clubs that i want to purchase however they are a little longer than I need by an inch and the lie has been changed by 2 degrees. It looks like i will need to get them changed for my height and swing. If I cut these custom shafts by an inch or an inch and a half will that affect the flex very much and will i possibly ruin the club? I know that changing the lie should have no affect but am concerned about changing the flex by cutting it.

Any advice would be appreciated...

Thanks!


  • Moderator
Posted

For every 1/2 inch you remove, you will lose approximately three swingweight points, making the club head feel lighter.  1 swing weight point equals to 1 CPM flex change.  You can readjust the swingweight by adding lead tape to the head of the club.  Any amount of cutting will slightly stiffen the club, for 1 inch it will make the shaft more stiff by a 1/2 flex.  Also if you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.

Mike McLoughlin

Check out my friends on Evolvr!
Follow The Sand Trap on Twitter!  and on Facebook
Golf Terminology -  Analyzr  -  My FacebookTwitter and Instagram 

Awards, Achievements, and Accolades

Posted

Can you hit these clubs before purchase? If so, I'd just choke down on them an inch or so and see how you hit them. If you can hit them off a lie board (while choking down 1") you can see if you'll need to have the lie adjusted or not. MVMAC is correct that shortening them an inch will make them play 2* flatter. This could be a good thing depending on what specs you need which is why I suggest hitting them off a lie board before making any alterations. If they were bent 2* upright and you play standard lie you will probably need to get them bent back.

MVMAC is also correct that each 1/2 inch you shorten the clubs will lighten the swing weight 3 points so shortening an inch will make it 6 points lighter. I doubt this will be an issue because my experience is that people that end up having longer shafts installed are usually playing with clubs that are way over the standard swing weight. The reason for this is because club heads come in standard weights and are designed to be built to standard lengths. So a guy that is taking a 38" 5 iron and extending it an inch is ADDING 6 points of swing weight from the "standard" weight that club was meant to be built at. The only way to adjust  this is to remove weight from the head which is almost impossible with irons so it is almost never done. SO, when you cut them down an inch the swing weight will be "standard" (assuming you going back to standard length)

“You don't have the game you played last year or last week. You only have today's game. It may be far from your best, but that's all you've got. Harden your heart and make the best of it.”

~ Walter Hagen


Posted

I have these clubs from a different store with stock shafts and standard lengths. These clubs are on Ebay from a guy i have bought some stuff off in the past so i know he is reputable just want to be sure that I can bend them back and cut an inch off without affecting the shaft too much. the custom shafts are DG R300 STEEL +1/2", 2 UP.


Posted

Cutting the 1/2 inch off is no big deal. If you regrip your own clubs it's a simple process of cutting off the grip and using a pipe cutter (plumber section of Home Depot) to cut the shaft. Then re-grip. Change in flex will be minimal as you are cutting the butt end. You didn't mention what type of heads but most cast head can be bent 2* with no issue.

The only issue you might have is if these clubs were originally built to standard length and then lengthened later. In this case they will have shaft extensions. These are easily removed using heat to break the epoxy bond.

“You don't have the game you played last year or last week. You only have today's game. It may be far from your best, but that's all you've got. Harden your heart and make the best of it.”

~ Walter Hagen


Note: This thread is 4979 days old. We appreciate that you found this thread instead of starting a new one, but if you plan to post here please make sure it's still relevant. If not, please start a new topic. Thank you!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Want to join this community?

    We'd love to have you!

    Sign Up
  • TST Partners

    PlayBetter
    Golfer's Journal
    ShotScope
    The Stack System
    FitForGolf
    FlightScope Mevo
    Direct: Mevo, Mevo+, and Pro Package.

    Coupon Codes (save 10-20%): "IACAS" for Mevo/Stack/FitForGolf, "IACASPLUS" for Mevo+/Pro Package, and "THESANDTRAP" for ShotScope. 15% off TourStriker (no code).
  • Posts

    • Day 1: 2025.12.26 Worked on LH position on grip, trying to keep fingers closer to perpendicular to the club. Feels awkward but change is meant to.
    • Please see this topic for updated information:
    • Please see this topic for updated information:
    • When you've been teaching golf as long as I have, you're going to find that you can teach some things better than you previously had, and you're probably going to find some things that you taught incorrectly. I don't see that as a bad thing — what would be worse is refusing to adapt and grow given new information. I've always said that my goal with my instruction isn't to be right, but it's to get things right. To that end, I'm about five years late in issuing a public proclamation on something… When I first got my GEARS system, I immediately looked at the golf swings of the dozens and dozens of Tour players for which I suddenly had full 3D data. I created a huge spreadsheet showing how their bodies moved, how the club moved, at various points in the swing. I mapped knee and elbow angles, hand speeds, shoulder turns and pelvis turns… etc. I re-considered what I thought I knew about the golf swing as performed by the best players. One of those things dated back to the earliest days: that you extend (I never taught "straighten" and would avoid using that word unless in the context of saying "don't fully straighten") the trail knee/leg in the backswing. I was mislead by 2D photos from less-than-ideal camera angles — the trail leg rotates a bit during the backswing, and so when observing trail knee flex should also use a camera that moves to stay perpendicular to the plane of the ankle/knee/hip joint. We have at least two topics here on this (here and here; both of which I'll be updating after publishing this) where @mvmac and I advise golfers to extend the trail knee. Learning that this was not right is one of the reasons I'm glad to have a 3D system, as most golfers generally preserve the trail knee flex throughout the backswing. Data Here's a video showing an iron and a driver of someone who has won the career slam: Here's what the graph of his right knee flex looks like. The solid lines I've positioned at the top of the backswing (GEARS aligns both swings at impact, the dashed line). Address is to the right, of course, and the graph shows knee flex from the two swings above. The data (17.56° and 23.20°) shows where this player is in both swings (orange being the yellow iron swing, pink the blue driver swing). You can see that this golfer extends his trail knee 2-3°… before bending it even more than that through the late backswing and early downswing. Months ago I created a quick Instagram video showing the trail knee flex in the backswing of several players (see the top for the larger number): Erik J. Barzeski (@iacas) • Instagram reel GEARS shares expert advice on golf swing technique, focusing on the critical backswing phase. Tour winners and major champions reveal the key to a precise and powerful swing, highlighting the importance of... Here are a few more graphs. Two LIV players and major champions: Two PGA Tour winners: Two women's #1 ranked players: Two more PGA Tour winners (one a major champ): Two former #1s, the left one being a woman, the right a man, with a driver: Two more PGA Tour players: You'll notice a trend: they almost all maintain roughly the same flex throughout their backswing and downswing. The Issues with Extending the Trail Knee You can play good golf extending (again, not "straightening") the trail knee. Some Tour players do. But, as with many things, if 95 out of 100 Tour players do it, you're most likely better off doing similarly to what they do. So, what are the issues with extending the trail knee in the backswing? To list a few: Pelvic Depth and Rotation Quality Suffers When the trail knee extends, the trail leg often acts like an axle on the backswing, with the pelvis rotating around the leg and the trail hip joint. This prevents the trail side from gaining depth, as is needed to keep the pelvis center from thrusting toward the ball. Most of the "early extension" (thrust) that I see occurs during the backswing. Encourages Early Extension (Thrust) Patterns When you've thrust and turned around the trail hip joint in the backswing, you often thrust a bit more in the downswing as the direction your pelvis is oriented is forward and "out" (to the right for a righty). Your trail leg can abduct to push you forward, but "forward" when your pelvis is turned like that is in the "thrust" direction. Additionally, the trail knee "breaking" again at the start of the downswing often jumps the trail hip out toward the ball a bit too much or too quickly. While the trail hip does move in that direction, if it's too fast or too much, it can prevent the lead side hip from getting "back" at the right rate, or at a rate commensurate with the trail hip to keep the pelvis center from thrusting. Disrupts the Pressure Shift/Transition When the trail leg extends too much, it often can't "push" forward normally. The forward push begins much earlier than forward motion begins — pushing forward begins as early as about P1.5 to P2 in the swings of most good golfers. It can push forward by abducting, again, but that's a weaker movement that shoves the pelvis forward (toward the target) and turns it more than it generally should (see the next point). Limits Internal Rotation of the Trail Hip Internal rotation of the trail hip is a sort of "limiter" on the backswing. I have seen many golfers on GEARS whose trail knee extends, whose pelvis shifts forward (toward the target), and who turn over 50°, 60°, and rarely but not never, over 70° in the backswing. If you turn 60° in the backswing, it's going to be almost impossible to get "open enough" in the downswing to arrive at a good impact position. Swaying/Lateral Motion Occasionally a golfer who extends the trail knee too much will shift back too far, but more often the issue is that the golfer will shift forward too early in the backswing (sometimes even immediately to begin the backswing), leaving them "stuck forward" to begin the downswing. They'll push forward, stop, and have to restart around P4, disrupting the smooth sequence often seen in the game's best players. Other Bits… Reduces ground reaction force potential, compromises spine inclination and posture, makes transition sequencing harder, increases stress on the trail knee and lower back… In short… It's not athletic. We don't do many athletic things with "straight" or very extended legs (unless it's the end of the action, like a jump or a big push off like a step in a running motion).
    • Day 135 12-25 Wide backswing to wide downswing drill. Recorder and used mirror. 
×
×
  • Create New...

Important Information

Welcome to TST! Signing up is free, and you'll see fewer ads and can talk with fellow golf enthusiasts! By using TST, you agree to our Terms of Use, our Privacy Policy, and our Guidelines.