Jump to content
Check out the Spin Axis Podcast! ×
Note: This thread is 6568 days old. We appreciate that you found this thread instead of starting a new one, but if you plan to post here please make sure it's still relevant. If not, please start a new topic. Thank you!

Recommended Posts

Posted
I play graphite shaft irons, +1/2" length, regular flex. The +1/2" length makes the regular flex feel even more flexible. How would trimming an extra 1/2" at the tip effect the flex? I would trim the butt end so that the clubs are still +1/2" over standard.

Thanks!

Posted
I'm just taking a stab at this, but when you build clubs/ look at a shaft without a head or grip you notice that the tip is a lot thicker than the butt end...its skinier, but thicker, so if you cut the tip off then it takes the thickest part of the shaft away making it able to bend just that much more...that is just my guess though. So i think trimming it a half inch would make it more flexible?
What's In The Bag?

Driver - Rapture 10.5 Epic 68g X-Pure - Balance Certified
Fairway Metal - Titleist PT 18°
Irons - Mizuno MP-67 3-PW Project X 6.0 Wedges - Mizunos R Series Chrome 52°, 56°, 58° Project X 6.0 Putter - Yes! C-Groove Callie-f - Balance Certified Bag - Ping Freestyle...

Posted
Dunno what will happen . Guess it would fine tune your shaft to fit your swing spec. have had this done befor to one of my sets ... have not felt any change in my short irons ... mid irons still held the distance ... long irons felt better ... Hope this gives light to the equation .

Posted
I play graphite shaft irons, +1/2" length, regular flex. The +1/2" length makes the regular flex feel even more flexible. How would trimming an extra 1/2" at the tip effect the flex? I would trim the butt end so that the clubs are still +1/2" over standard.

melraid,

Trimming half an inch off the butt will do nothing to the dynamic flex. However, it would slightly stiffen the club since you are swinging a shorter lever it will not flex as much. However, this will be very slight and virtually negligible. What you will notice is a slower swing speed and possibly reduced distance (assuming you make good contact at the half inch over length). Also, if you fit into a half inch long club, moving down a half inch will likely result in a lot of toe hits at impact and contact away from center will always cost you distance.

Posted
mainly just wondering if trimming an extra 1/2" off the tip, and leaving the extra 1/2" on the butt end so the overall length remains the same. Seems it would make it stiffer.

Posted
Tip trimming will stiffen the flex of the shaft. I believe it's called Hard stepping. Causing the actual flex of say a reg. to play stiff.

:tmade: R15 14* Matrix Black Tie 7m3

:adams: Speedline Super S 3w & 5w Matrix Radix HD S VI

:callaway: X-12 4-PW Memphis 10

IONNOVEX  Type S GDT 50*, 54* & 62* Mitsubishi Rayon Kuro Kage Black 80ir

:odyssey: Tri-Ball SRT

-Landon


Posted
Tip trimming will stiffen the flex of the shaft. I believe it's called Hard stepping. Causing the actual flex of say a reg. to play stiff.

I don't think so. As far as I know, hard-stepping refers to the method of stiffening shaft flex by installing the original shaft meant for a lower iron to a higher iron. You do it the other way and it's called soft-stepping. For example, PW's shaft goes to 9-iron (Hard) or 9-iron's shaft goes to PW (Soft).

What's in the bag:
Driver: r7 SuperQuad 10.5° ~ UST Proforce V2 65g Regular
Wood: 906F4 18.5° ~ Aldila VS Proto 80g Stiff
Irons: MP-60 3-PW ~ True Temper Tour Concept S3
Wedges: Vokey Oil Can 252.08, SM56.10 & SM60.08Putter: Marxman Mallet 33"

Posted
mainly just wondering if trimming an extra 1/2" off the tip, and leaving the extra 1/2" on the butt end so the overall length remains the same. Seems it would make it stiffer.

melraid,

This will stiffen the shaft. However, you must be very careful in selecting a club to do this with since it will only work with parallel (.370 or unitized) shafts. Most OEM's today use .355 taper tip shafts, if you trim a half inch off them they will no longer fit properly in the hosel. That is why most clubmakers use hard and soft stepping to fine tune flex with taper tip shafts rather than tip trimming. As fusioncal correctly stated, hard stepping is where you take a shaft meant for an eight iron and put it in the seven iron head. This way a shorter tip or taper section is used giving the club a tighter feel. Softstepping would be the reverse. In summary, if your clubs are .370 hosels, you can tip trim. If they are .355 taper tip, you must either hard or soft step.

Note: This thread is 6568 days old. We appreciate that you found this thread instead of starting a new one, but if you plan to post here please make sure it's still relevant. If not, please start a new topic. Thank you!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Want to join this community?

    We'd love to have you!

    Sign Up
  • TST Partners

    PlayBetter
    Golfer's Journal
    ShotScope
    The Stack System
    FitForGolf
    FlightScope Mevo
    Direct: Mevo, Mevo+, and Pro Package.

    Coupon Codes (save 10-20%): "IACAS" for Mevo/Stack/FitForGolf, "IACASPLUS" for Mevo+/Pro Package, and "THESANDTRAP" for ShotScope. 15% off TourStriker (no code).
  • Posts

    • Day 1: 2025.12.26 Worked on LH position on grip, trying to keep fingers closer to perpendicular to the club. Feels awkward but change is meant to.
    • Please see this topic for updated information:
    • Please see this topic for updated information:
    • When you've been teaching golf as long as I have, you're going to find that you can teach some things better than you previously had, and you're probably going to find some things that you taught incorrectly. I don't see that as a bad thing — what would be worse is refusing to adapt and grow given new information. I've always said that my goal with my instruction isn't to be right, but it's to get things right. To that end, I'm about five years late in issuing a public proclamation on something… When I first got my GEARS system, I immediately looked at the golf swings of the dozens and dozens of Tour players for which I suddenly had full 3D data. I created a huge spreadsheet showing how their bodies moved, how the club moved, at various points in the swing. I mapped knee and elbow angles, hand speeds, shoulder turns and pelvis turns… etc. I re-considered what I thought I knew about the golf swing as performed by the best players. One of those things dated back to the earliest days: that you extend (I never taught "straighten" and would avoid using that word unless in the context of saying "don't fully straighten") the trail knee/leg in the backswing. I was mislead by 2D photos from less-than-ideal camera angles — the trail leg rotates a bit during the backswing, and so when observing trail knee flex should also use a camera that moves to stay perpendicular to the plane of the ankle/knee/hip joint. We have at least two topics here on this (here and here; both of which I'll be updating after publishing this) where @mvmac and I advise golfers to extend the trail knee. Learning that this was not right is one of the reasons I'm glad to have a 3D system, as most golfers generally preserve the trail knee flex throughout the backswing. Data Here's a video showing an iron and a driver of someone who has won the career slam: Here's what the graph of his right knee flex looks like. The solid lines I've positioned at the top of the backswing (GEARS aligns both swings at impact, the dashed line). Address is to the right, of course, and the graph shows knee flex from the two swings above. The data (17.56° and 23.20°) shows where this player is in both swings (orange being the yellow iron swing, pink the blue driver swing). You can see that this golfer extends his trail knee 2-3°… before bending it even more than that through the late backswing and early downswing. Months ago I created a quick Instagram video showing the trail knee flex in the backswing of several players (see the top for the larger number): Erik J. Barzeski (@iacas) • Instagram reel GEARS shares expert advice on golf swing technique, focusing on the critical backswing phase. Tour winners and major champions reveal the key to a precise and powerful swing, highlighting the importance of... Here are a few more graphs. Two LIV players and major champions: Two PGA Tour winners: Two women's #1 ranked players: Two more PGA Tour winners (one a major champ): Two former #1s, the left one being a woman, the right a man, with a driver: Two more PGA Tour players: You'll notice a trend: they almost all maintain roughly the same flex throughout their backswing and downswing. The Issues with Extending the Trail Knee You can play good golf extending (again, not "straightening") the trail knee. Some Tour players do. But, as with many things, if 95 out of 100 Tour players do it, you're most likely better off doing similarly to what they do. So, what are the issues with extending the trail knee in the backswing? To list a few: Pelvic Depth and Rotation Quality Suffers When the trail knee extends, the trail leg often acts like an axle on the backswing, with the pelvis rotating around the leg and the trail hip joint. This prevents the trail side from gaining depth, as is needed to keep the pelvis center from thrusting toward the ball. Most of the "early extension" (thrust) that I see occurs during the backswing. Encourages Early Extension (Thrust) Patterns When you've thrust and turned around the trail hip joint in the backswing, you often thrust a bit more in the downswing as the direction your pelvis is oriented is forward and "out" (to the right for a righty). Your trail leg can abduct to push you forward, but "forward" when your pelvis is turned like that is in the "thrust" direction. Additionally, the trail knee "breaking" again at the start of the downswing often jumps the trail hip out toward the ball a bit too much or too quickly. While the trail hip does move in that direction, if it's too fast or too much, it can prevent the lead side hip from getting "back" at the right rate, or at a rate commensurate with the trail hip to keep the pelvis center from thrusting. Disrupts the Pressure Shift/Transition When the trail leg extends too much, it often can't "push" forward normally. The forward push begins much earlier than forward motion begins — pushing forward begins as early as about P1.5 to P2 in the swings of most good golfers. It can push forward by abducting, again, but that's a weaker movement that shoves the pelvis forward (toward the target) and turns it more than it generally should (see the next point). Limits Internal Rotation of the Trail Hip Internal rotation of the trail hip is a sort of "limiter" on the backswing. I have seen many golfers on GEARS whose trail knee extends, whose pelvis shifts forward (toward the target), and who turn over 50°, 60°, and rarely but not never, over 70° in the backswing. If you turn 60° in the backswing, it's going to be almost impossible to get "open enough" in the downswing to arrive at a good impact position. Swaying/Lateral Motion Occasionally a golfer who extends the trail knee too much will shift back too far, but more often the issue is that the golfer will shift forward too early in the backswing (sometimes even immediately to begin the backswing), leaving them "stuck forward" to begin the downswing. They'll push forward, stop, and have to restart around P4, disrupting the smooth sequence often seen in the game's best players. Other Bits… Reduces ground reaction force potential, compromises spine inclination and posture, makes transition sequencing harder, increases stress on the trail knee and lower back… In short… It's not athletic. We don't do many athletic things with "straight" or very extended legs (unless it's the end of the action, like a jump or a big push off like a step in a running motion).
    • Day 135 12-25 Wide backswing to wide downswing drill. Recorder and used mirror. 
×
×
  • Create New...

Important Information

Welcome to TST! Signing up is free, and you'll see fewer ads and can talk with fellow golf enthusiasts! By using TST, you agree to our Terms of Use, our Privacy Policy, and our Guidelines.