Jump to content
Check out the Spin Axis Podcast! ×
Note: This thread is 5619 days old. We appreciate that you found this thread instead of starting a new one, but if you plan to post here please make sure it's still relevant. If not, please start a new topic. Thank you!

Recommended Posts

Posted

I was at the Ping Office in Phoenix and had their free fitting. I dont have all the stats about clubspeed, ballspeed, lanch angles etc.

I currently hit a 10.5 driver. When I strike it well it goes 260 plus yards. But I am inconsistent with the driver. My miss is to the right but generally I can hit a mid - low shot like a line drive. At Ping they said I was not generating enough spin with my 10.5 which they said was costing me yards as the spin will add carry. They recommended at 13 deg G15 with a stiff TFC149 or 12.5 deg with reg TFC149 shaft. I demoed the 13 deg on a course I essentially ballooned every tee shot. It was straight but 10-15 yards shorter than my 10.5.

I returned home went to the Ping fitter and he aggreed I needed more loft to get more spin. But after watching me hit he felt a stiff TFC 149 with a 12 deg would be sufficient. Basically saying more spin more height more carry more accuracy.

Any thoughts on this?


Posted

You must be something right to reach 260 yards, even if it's only occasionally.

Maybe try a higher spin ball with your 10.5* first before spending cash on a higher lofted driver.


Posted

No they can't change the loft on a driver. Are you sure they said you needed more spin and not a higher launch angle? You went for a fitting and the information you were provided would be just as useful for the people on the forum in deciphering what would be good for you.

« Keith »


Posted


Originally Posted by wrx_junki

No they can't change the loft on a driver. Are you sure they said you needed more spin and not a higher launch angle? You went for a fitting and the information you were provided would be just as useful for the people on the forum in deciphering what would be good for you.


I agree...I'm curious as well...

PING K15 Driver
Tour Edge 4 Wood
PING K15 7 Wood
PING i15 Hybrid
PING Zing-2 Irons


Note: This thread is 5619 days old. We appreciate that you found this thread instead of starting a new one, but if you plan to post here please make sure it's still relevant. If not, please start a new topic. Thank you!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Want to join this community?

    We'd love to have you!

    Sign Up
  • TST Partners

    Carl's Place
    PlayBetter
    Golfer's Journal
    ShotScope
    The Stack System
    FitForGolf
    FlightScope Mevo

    Coupon Codes (save 10-20%): "IACAS" for Mevo/Stack/FitForGolf, "IACASPLUS" for Mevo+/Pro Package, and "THESANDTRAP" for ShotScope. 15% off TourStriker (no code).
  • Posts

    • Probably since the golfer has to swing the club back and up. The hands have to move back and up. You can feel them go back and up just by turning the shoulders and bending the right arm, because it brings your hands towards your right shoulder.  The difference is if you maintain width or not. Less width means a shorter feeling swing path so the more you need to lift the arms. Being as someone who gets the right arm bend at 110+ degrees, it's 100% a timing issue. I am use to like a 1.5+ second backswing. It probably should be like 1 second at most. Half a second or more will feel like an eternity. I have had swings where I keep my right arm straighter and I am still trying to time the downswing based on the old tempo.  Ideally, for me, it is probably going to be a much quicker and shorter (in duration) backswing, while keeping the right elbow straighter. Which also means more hinging to get swing length without over swinging. 
    • Wordle 1,789 5/6 ⬜⬜⬜⬜⬜ ⬜⬜🟨⬜⬜ ⬜🟩⬜🟩🟩 ⬜🟩🟨🟩🟩 🟩🟩🟩🟩🟩
    • I'm currently recuperating from surgery, so no golf, but have been thinking about this quite a bit. This and the don't overbend the right arm thing. It's hard for me to even pose the position, so I'm not 100% sure, but I feel like it's impossible to have the right humerus along the shirt seam and not overbend your right arm, unless your hands are down near your hips. If the left arm is up at or above the shoulder plane and your right arm is bent less than 90 degrees, then your right humerus has to raise or your hands will get pulled apart. Your left hand can't reach your right hand unless either the right upper arm is up or the right arm is overbent. Is that right? If it is, then focusing on not overbending the right arm would force you to raise the humerus. And actually thinking further on it, if you do overbend your right arm, then you're basically forcing your upper arm down or forcing your left arm to bend. Since (for me at least) bending the left arm too much is not something I think I need to worry about, it means that the bend in the trail arm is really the driving force behind what happens to the right humerus. 
    • I managed to knock off a 3, a 13, and a 15 a couple of weeks ago. The 3 was a 185 yard par 3 with a 6 iron to 12 feet. 13 was a 350 yard par 4, which was a 2 iron and a 9 iron to about a foot. 15 was a 560 yard par 5 with a driver in a bunker, 4 iron into the semi, gap wedge to 8 feet and a putt.
    • Wordle 1,789 4/6* ⬜⬜⬜⬜⬜ ⬜⬜🟨⬜⬜ 🟨🟩⬜⬜🟩 🟩🟩🟩🟩🟩
×
×
  • Create New...

Important Information

Welcome to TST! Signing up is free, and you'll see fewer ads and can talk with fellow golf enthusiasts! By using TST, you agree to our Terms of Use, our Privacy Policy, and our Guidelines.