Jump to content
Check out the Spin Axis Podcast! ×
Check out the Spin Axis Podcast!
IGNORED

Maltby Clubmaking/Repair Manual

Buzzy

By Buzzy
in Clubs, Grips, Shafts, Fitting

 Share
Note: This thread is 2370 days old. We appreciate that you found this thread instead of starting a new one, but if you plan to post here please make sure it's still relevant. If not, please start a new topic. Thank you!

Recommended Posts

Buzzy Member

Buzzy

Posted
Posted

Does anyone have a copy of this?  It is the hard copy one that is over 500 pages.  In the older edition there was a section that showed each shaft and gave specs on them including weight, trim instructions, tip length, step pattern etc.  It contained the specs for all the common steel shaft from the 60s-80s.  I am trying to find this information on the TT JetStep steel shaft.


Vinsk Incredible Member

Vinsk

Posted
Posted

@Adam C...paging Adam....

:ping: G25 Driver Stiff :ping: G20 3W, 5W :ping: S55 4-W (aerotech steel fiber 110g shafts) :ping: Tour Wedges 50*, 54*, 58* :nike: Method Putter Floating clubs: :edel: 54* trapper wedge

Awards, Achievements, and Accolades
1
1

denkea Member

denkea

Posted
Posted (edited)

Wood - UJWC = 1" steps.  .600 butt dia.  .335 tip.  47".  131 grams.  

 

Irons - UJIC(.370) UJCIO (.395) = 1" steps.  .600 butt dia.  41".  129 grams

 

irons - JTIS/JTISR = 1" steps.  .580 butt dia.  .355 tip dia.  35"-39" 120 grams

 

All I could find on trimming is pretty much the standard.  0" for 1 iron/1/2" for 2 iron/1" for 3 iron, etc.  

HTH

 

Edited by denkea
tip dia correction

Buzzy Member

Buzzy

Posted
  • Author
Posted

mine are the UJCIO (over hosel)  I am trying to fix up an old set of Spalding XE hyprid irons.  Some of the shafts look like they have been cut  because they broke off at the hosel etc.  Knowing the raw length should help me figure this out.  The PW is the worst while the 3 iron is off about an inch.  Thanks


denkea Member

denkea

Posted
Posted (edited)
2 hours ago, Buzzy said:

mine are the UJCIO (over hosel)  I am trying to fix up an old set of Spalding XE hyprid irons.  Some of the shafts look like they have been cut  because they broke off at the hosel etc.  Knowing the raw length should help me figure this out.  The PW is the worst while the 3 iron is off about an inch.  Thanks

Wow!  Good luck with that.  I don't envy you that job.  But,,,,,have fun though.

Edited by denkea

Buzzy Member

Buzzy

Posted
  • Author
Posted

thanks, i think i will need to tip some shafts and extend the length is some

the guy that had these put brand new grips on them in order to sell them;  they did not sell so my friend who owns the course just gave them to me as he knows i tinker with clubs


Note: This thread is 2370 days old. We appreciate that you found this thread instead of starting a new one, but if you plan to post here please make sure it's still relevant. If not, please start a new topic. Thank you!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Want to join this community?

    We'd love to have you!

    Sign Up

  • TST Partners

    PlayBetter
    Golfer's Journal
    ShotScope
    The Stack System
    FitForGolf
    FlightScope Mevo
    Direct: Mevo, Mevo+, and Pro Package.

    Coupon Codes (save 10-20%): "IACAS" for Mevo/Stack/FitForGolf, "IACASPLUS" for Mevo+/Pro Package, and "THESANDTRAP" for ShotScope. 15% off TourStriker (no code).

  • Posts

    • 5amZ
      "5 Minutes Daily" Practice Challenge

      By 5amZ · Posted

      Day 159 1-19 Flow drill while attempting to add arch in wrist on downswing. Not where it needs to be but felt good working on swing flow. 
    • WillieT
      "5 Minutes Daily" Practice Challenge

      By WillieT · Posted

      Day 1 (19 Jan 26) - after a week lay-off due to travels, felt great to get in some drills in the backyard today.  Started with lead arm only short pitches focused on squared face and light divot post ball.  Haven’t done this in a while and it showed, with some skulls and slices.  Settled into easy flighted balls - wrapped up with standard two handed swings.  Good restart to the daily drills. 
    • Shindig
      Golf Workouts

      By Shindig · Posted

      That depends what you do within those two.  Are they your only options?   Check out Fit for Golf if you get a moment.  It's linked on the sidebar;  I did it for two years, stopped for a really bad reason, and I plan to get back to it soon.   Mike Carroll also has a great free podcast about a lot of topics in golf fitness. 
    • Shindig
      "5 Minutes Daily" Practice Challenge

      By Shindig · Posted

      Day 19, 1/19.  Finished work in time to spend 25 minutes hitting balls (hit 15) indoors, off a mat, into the net.  Usual focus.    
    • Chris Brooks
      "5 Minutes Daily" Practice Challenge

      By Chris Brooks · Posted

      Day 30 - 2026-01-19 Got 10 minutes in on the mat / net working on exagerrating movements I'm working on. And grip. Also worked with my friendly AI to summarize key negative tendencies I have so that I can build a personal checklist to follow. Will do more mirror work tonight.
×
×
  • Create New...

Important Information

Welcome to TST! Signing up is free, and you'll see fewer ads and can talk with fellow golf enthusiasts! By using TST, you agree to our Terms of Use, our Privacy Policy, and our Guidelines.

  I accept